Westchester County, NY · ~50 min away
Mold Remediation & Removal in Yonkers, NY
Sealed containment, removal of what's colonized, and a fix for the moisture behind it.
Westchester County, NY · ~50 min away
Mold Remediation & Removal in Yonkers, NY
Mold grows because something is wet, so the first job is finding the water. Removal happens under sealed containment, and the moisture source gets fixed before we call it done. Yonkers is about 50 minutes out for us.
Yonkers buried a river to manage flooding: the Saw Mill was culverted under Getty Square in the 1920s and only daylighted again in 2011. The valley it drains still collects the city's water, so the low blocks near the Saw Mill corridor are where storm calls concentrate.
Free inspection with a written scope before any work begins. Covered claims are billed directly to your insurance carrier.
Local knowledge
What we see in Yonkers
The housing stock, the terrain, and the drainage in Yonkers all change how we plan a job. Here's what we run into:
The housing stock
Pre-war buildings dominate: plaster and lath, tile bathrooms on wood subfloors, stone foundations. They hold moisture far longer than drywall-era construction, so we meter deep and keep the equipment running until the wall reads dry, not just the surface.
Getting to you
About 50 minutes down the Thruway. For apartment buildings we handle superintendent coordination, COIs where boards require them, and elevator and stair protection as standard practice.
Water & drainage
The city is a series of steep hills draining to the Saw Mill valley and the Hudson. Rain leaves the heights fast and collects in the valley neighborhoods, which is why the river got buried in the first place.
Process
How the job goes.
Containment goes up first, the affected material comes out second, and the moisture source gets fixed before we finish. Here's the short version; the service page explains each step and why the order matters.
- 01
Inspect & find the moisture
Every mold job starts as a water investigation. Moisture meters and thermal imaging trace where the water comes from: a leak, condensation, ground moisture, or a bath fan venting into the attic. Remove the mold without stopping the water and it grows back.
- 02
Contain the work area
Plastic containment seals the affected area, and negative air machines with HEPA filtration keep airflow moving into the zone rather than out of it. Without containment, the work itself spreads spores into rooms that were clean.
- 03
Remove what's colonized
Porous materials with growth (drywall, insulation, carpet) get bagged inside containment and removed; they can't be reliably cleaned. Framing and other structural wood gets HEPA-vacuumed, cleaned, and treated as its condition calls for.
- 04
Clean the air & surfaces
HEPA air scrubbers run throughout, then every surface in the containment gets HEPA-vacuumed and damp-wiped. The S520 standard for finishing is a work area that is visibly clean, dust-free, and odor-free, and that's what we clean to.
- 05
Fix the moisture source
This is the repair that ends the problem: the leak fixed, the bath fan vented outside, the grading or gutter issue named in writing. We handle what's in our scope and tell you who to call for what isn't.
- 06
Verify
Final walkthrough against the written scope. If you want lab numbers behind the visual standard, we arrange third-party clearance testing, and that lab reports to you rather than to us.
Heavy rain in the forecast
After a storm floods the basement in Yonkers: the mold clock
Storm water in a basement turns into a mold job when the drying waits. Here is what matters in the first day.
In the first day
- Wet materials start growing mold in 24 to 48 hours. Drying fast is the mold prevention.
- Do not run the furnace fan or box fans to dry the house. They move damp air and spores through every room.
- If a floor drain or toilet backed up with the rain, the water is contaminated and porous materials it touched have to come out.
Full walkthrough: what to do when your basement floods in a storm. Water in the house now? Call (845) 262-6530. Same-day emergency response, six days a week.
Common problems
The problems we're usually called about.
Black mold behind a wall, under a sink, or on the ceiling
The color doesn't change the job. Black mold removal follows the same steps as any other active growth: find the moisture, contain the area, remove what's colonized, clean and dry what stays. We do the mold cleanup and the repair to the wall or ceiling afterward, under one scope.
A closet on an exterior wall grows mold every winter
A cold exterior wall, warm humid indoor air, and no circulation behind the stored boxes add up to condensation. We remediate the growth and tell you what stops it: air movement, insulation where it's missing, and humidity control. It's a small job if the cause gets addressed.
Attic sheathing turned dark after years of a bath fan venting up there
A bath fan pushing moist air into the attic grows mold across the underside of the roof deck. We remediate the sheathing, and the duct has to be rerouted outside as part of the job. Without that, the sheathing darkens again within a few winters.
Worried about what the kids are breathing
Mold can trigger allergy and asthma symptoms, and sensitivity varies from person to person. That's the EPA's position and ours. We'll tell you what we found, scope the work to match it, fix the moisture, and put the findings in writing.
Insurance
We work with your insurance, and we bill them directly
- 01
Call us
We answer, ask what happened, and get a crew moving. Same-day emergency response on active water.
- 02
We document everything
We take moisture readings and photos and write up a scope of work before drying starts, so your adjuster has the file from day one.
- 03
We bill your insurer directly
We work directly with your insurance company on covered water and mold claims, so you're not fronting the full cost and chasing reimbursement.
Your deductible is still yours to cover. Your declarations page or your agent has the exact number, and we ask for it before any work starts rather than after. You also don't need a claim to hire us. Plenty of our jobs are paid directly by the homeowner, and after the free inspection you get a written estimate to make that decision with.
Not insurance advice. We're a restoration contractor, not a public adjuster or insurance agent. Coverage decisions belong to your insurer, so confirm anything about your policy with your agent or adjuster.
Who's showing up
Local and independent since 2019.
The person on the phone is the person planning the job. We're in Yonkers every week.
- IICRC Certified
- Licensed
- Bonded
- Insured
- Eco-Conscious Products
FAQ
Questions we get most.
Does homeowners insurance cover water damage?
That's a question for your insurer, and we say so on purpose. We're a restoration contractor, not a public adjuster or insurance agent, and only your carrier can tell you what your policy covers. In general terms, homeowners policies treat sudden and accidental damage, like a burst pipe or a failed water heater, differently from a slow leak that ran for months, and flooding from outside is usually a separate policy. That's why the cause of loss matters. When we inspect, we photograph and log what the damage shows, and that record goes to your insurer for their decision. Call your agent or your carrier's claim line to confirm coverage before you count on it.
Is mold in my house dangerous?
Mold can irritate eyes, nose, and throat, trigger allergic reactions like sneezing and skin rash, and aggravate asthma in people who have it. Sensitivity varies a lot from person to person. That's the EPA's position and ours. It's worth taking seriously, and it's not a reason to panic. Mold is a moisture problem in the house, and it's a fixable one.
What's the difference between mold removal and mold remediation?
"Mold removal" is a misleading term. Spores exist naturally everywhere, indoors and out, so no company can remove all mold from a house. Remediation is the accurate word: contain the affected area, take out materials too far gone, clean what can be cleaned, filter the air, and fix the moisture problem that caused the growth. Skip that last step and the mold comes back no matter how thorough the cleanup was.
What is containment and why does it matter?
Containment keeps a mold problem in one room. Disturbing moldy material sends spores airborne, so before any demolition we seal the work area with plastic sheeting, cover HVAC vents, and run HEPA-filtered machines that hold the space under negative pressure, meaning air flows in and not out. Without it, cutting out moldy drywall spreads spores through the rest of the house.
How long does mold remediation take?
One to two days for a small, contained area like a patch behind a vanity or a closet wall. Multiple rooms, flooring removal, or a wet structure that has to be dried first runs several days to a week or more. Repairing the source and rebuilding usually add more time than the remediation itself. After the inspection you get a schedule with each of those steps laid out.
Service area
Yonkers, NY — Westchester County.
We're about 50 minutes out, six days a week. The homes run to pre-war apartment buildings, early-1900s Victorians and rowhouses on the hills, and post-war homes toward the east side. We cover every block, including Getty Square, Park Hill, Ludlow Park. Yonkers is known for the daylighted Saw Mill River at Van der Donck Park, the Hudson River Museum, and Untermyer Park's gardens.
Also in Yonkers
Mold Remediation in nearby towns
Free inspection
Start with a free inspection in Yonkers.
Call or send the form. We look, we measure, and you get a written scope and a straight answer. Sometimes that answer is that the work can wait.
Office hours: Mon–Fri 8am–6pm · Sun 8am–6pm · Closed Saturdays.